Perth Intumescent Paint. Qualified Applicator - 90 and 120 minute fire resistance. Australian Fire Control.

May 2, 2017

Intumescent Paint Fire Rated Coating Systems for Structural Steel. Australian Fire Control is a qualified applicator of 1120PRODUCT DESCRIPTION Supplied/Installed/Certified/Maintained 

Interchar 1120 Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance  

 

 

 

 

 

 

 

1120 A single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. Interchar 1120 is a low VOC acrylic intumescent material independently fire tested for up to 3 hour fire ratings in accordance with ASTM E119/UL263, BS 476 20-22, EN 13381-8 and GB 14907. Interchar 1120 is a CE marked product with European Technical Approval ETA-11/0045.

INTENDED USES
To provide cellulosic fire protection on beams, columns and hollow sections in interior environments.

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application, all steel surfaces should be assessed and treated in accordance with ISO 8504:2000. Oil or grease should be removed in accordance with SSPC-SP1 Solvent Cleaning.

Primed Steelwork Interchar 1120 should always be applied over a recommended anti-corrosive coating scheme. The primer surface should be dry and free from all contamination and Interchar 1120 must be applied within the overcoating intervals specified (consult the Interchar 1120 Application Guidelines). Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa21⁄2 (ISO 8501-1:2007) or SSPC-SP6, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and a full coat of primer applied prior to overcoating with Interchar 1120.

Metallic Zinc Primed Surfaces Interchar 1120 can be applied over approved epoxy metallic zinc primers, provided that these have been overcoated with an approved tie coat. Ensure that the primed surface is clean, dry and free from contamination prior to application of the Interchar 1120. Recommended tie coats are Intergard 269 or Intergard 276.

Interchar 1120 Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance

Typical uses Provides intumescent fire protection to structural steelwork while maintaining architectural aesthetics for commercial infrastructure assets including:
• Airports
• Stadia and leisure facilities
• Office buildings
• Retail complexes

One supplier, one solution Project construction aspects and client aesthetic requirements may require the use of both a primer and colored topcoats. You can have confidence in AkzoNobel and its International® range due to our commitment to testing complete systems and offering a single point of supply and support.

Testing to the highest standard The Certifire system involves type testing and audit testing for fire and non-fire performance together with factory production control. It is important to know that the products supplied and installed will provide the same level of performance as those tested.
Interchar® 1120 has been tested to the ASFP protocol to account for beams with web openings. This permits optimized dry film thicknesses to be specified for beams with circular, rectangular and castellated openings.

Approvals
BS 476 Parts 20-21: Fire Resistance of Elements of Construction
AS 1530.4: Fire Resistance Test of Elements of Construction
UL 263: Fire Tests of Building Construction and Materials
GB 14907: Guobiao - Chinese National Standard

Fire protection with aesthetic appeal Interchar® 1120 has been designed to allow fireproofing without compromising aesthetic appeal:
• Competitive dry film thicknesses
• Applied as a thin layer, it does not compromise intricate designs and shapes created from the structural steel
• Easy over-coating with a wide range of colored finishes

Check out all Structural Steel protection systems available from Australian Fire Control.

Contact Australian Fire Control
Phone: 9399 6957
Email: Sales@AustralianFireControl.com.au
Web: www.AustralianFireControl.com.au
 

Please reload

Western Australian

Head Office

Phone: 9399 6957

Address: 17 Williams Road Kelmscott WA 6111
Postal: PO BOX 1008 DC Kelmscott WA 6997
Email: Sales@AustralianFireControl.com.au

  • LinkedIn Social Icon
  • Facebook Social Icon
  • Google+ Social Icon
  • YouTube Social  Icon
  • Instagram Social Icon

Australian Fire Control offer a large versatile range of specialist fire, smoke & ballistic resistant systems tested
and certified to Australian Standards.